Running transformation scenario on Dita map fails because th
Posted: Wed May 15, 2013 6:37 pm
Hello,
I am using <oXygen/> XML Editor 14.2 build 2013051016.
Here is a short example to explain my problem.
I first create a concept topic (let us call it concept1.dita) of category 'DITA / topic-xsd'.
I fill it in a bit and then run a transformation scenario on it.
The topic gets suitably transformed. The result of the transformation is thus OK.
I now create a DITA map of category 'DITA Map / map-xsd'.
I then add concept1.dita to the DITA map and save the DITA map afterwards.
Running a transformation scenario on the DITA map gives the following error messages on concept1.dita:
[DOTJ030I] No 'class' attribute for was found for element '<concept>'. This generally indicates that your DTD or Schema was not developed properly according to the DITA specification.
[DOTJ030I] No 'class' attribute for was found for element '<title>'. This generally indicates that your DTD or Schema was not developed properly according to the DITA specification.
and so on for each other element in concept1.dita.
Moreover, as confirmed by the following error message, concept1.dita does not get transformed:
[DOTJ021W] File 'concept1.dita' will not generate output since it is invalid or all of its content has been filtered out by the ditaval file. Please check the file 'concept1.dita' and the ditaval file to see if this is the intended result.
Validation tests run on concept1.dita and on the DITA map say that these documents are valid.
Strangely enough, doing the same test with a concept of category 'DITA / topic' and a DITA map of category 'DITA Map / Map' works fine. That is, the concept gets suitably transformed in the two cases.
Strangely enough too, this problem was not present in <oXygen/> XML Editor 14.0 build 2012080717, which I was using before upgrading to version 14.2.
I am using <oXygen/> XML Editor 14.2 build 2013051016.
Here is a short example to explain my problem.
I first create a concept topic (let us call it concept1.dita) of category 'DITA / topic-xsd'.
I fill it in a bit and then run a transformation scenario on it.
The topic gets suitably transformed. The result of the transformation is thus OK.
I now create a DITA map of category 'DITA Map / map-xsd'.
I then add concept1.dita to the DITA map and save the DITA map afterwards.
Running a transformation scenario on the DITA map gives the following error messages on concept1.dita:
[DOTJ030I] No 'class' attribute for was found for element '<concept>'. This generally indicates that your DTD or Schema was not developed properly according to the DITA specification.
[DOTJ030I] No 'class' attribute for was found for element '<title>'. This generally indicates that your DTD or Schema was not developed properly according to the DITA specification.
and so on for each other element in concept1.dita.
Moreover, as confirmed by the following error message, concept1.dita does not get transformed:
[DOTJ021W] File 'concept1.dita' will not generate output since it is invalid or all of its content has been filtered out by the ditaval file. Please check the file 'concept1.dita' and the ditaval file to see if this is the intended result.
Validation tests run on concept1.dita and on the DITA map say that these documents are valid.
Strangely enough, doing the same test with a concept of category 'DITA / topic' and a DITA map of category 'DITA Map / Map' works fine. That is, the concept gets suitably transformed in the two cases.
Strangely enough too, this problem was not present in <oXygen/> XML Editor 14.0 build 2012080717, which I was using before upgrading to version 14.2.